instalace wifi adapteru

[kucmais]

Výpis
Bus 001 Device 002: Id 148f:7601 Ralink Technology, Corp
Já vím že je slabý, je v dílně primárně na manuály a návody, na internet jen když je třeba něco dohledat.

[kucmais]

Dell OP755 mini za 1200,- s 2GB treba mame zrovna na sklade

mohl bych vědět kde, nebo poštou?

[Ventero1]

1. Takze system ji vidi. Bude to tedy nejspis otazka nejakeho proprietalniho a bude treba se poprat s tou instalaci. Pripoj do,dalsiho prispevku soubor readme, popr. dalsi textove soubory, at to muzeme procist.

2. V Sokolove, mozna jeste i v Karlovych Varech. Ale klidne i postou.

[kucmais]

soubor readme sta usb
* README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

=======================================================================
ModelName:
===========
RT2870 Wireless Lan Linux Driver


=======================================================================
Driver lName:
===========
rt2870.o/rt2870.ko


=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.


=======================================================================
Ralink Hardware:
===================
Ralink 802.11n Wireless LAN Card.


=======================================================================
Description:
=============
This is a linux device driver for Ralink RT2870 USB ABGN WLAN Card.


=======================================================================
Contents:
=============
Makefile : Makefile
*.c : c files
*.h : header files


=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
open or shared or WPA-PSK or WPA2-PSK authentication method.
NONE, WEP, TKIP and AES encryption.


=======================================================================
Build Instructions:
====================

1> $tar -xvzf DPB_RT2870_Linux_STA_x.x.x.x.tgz
go to "./DPB_RT2870_Linux_STA_x.x.x.x" directory.

2> In Makefile
set the "MODE = STA" in Makefile and chose the TARGET to Linux by set "TARGET = LINUX"
define the linux kernel source include file path LINUX_SRC
modify to meet your need.

3> In os/linux/config.mk
define the GCC and LD of the target machine
define the compiler flags CFLAGS
modify to meet your need.
** Build for being controlled by NetworkManager or wpa_supplicant wext functions
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y'.
=> #>cd wpa_supplicant-x.x
=> #>./wpa_supplicant -Dwext -ira0 -c wpa_supplicant.conf -d
** Build for being controlled by WpaSupplicant with Ralink Driver
Please set 'HAS_WPA_SUPPLICANT=y' and 'HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n'.
=> #>cd wpa_supplicant-0.5.7
=> #>./wpa_supplicant -Dralink -ira0 -c wpa_supplicant.conf -d

4> $make
# compile driver source code
# To fix "error: too few arguments to function ˇĄiwe_stream_add_event"
=> $patch -i os/linux/sta_ioctl.c.patch os/linux/sta_ioctl.c

5> $cp RT2870STA.dat /etc/Wireless/RT2870STA/RT2870STA.dat

6> load driver, go to "os/linux/" directory.
#[kernel 2.4]
# $/sbin/insmod rt2870sta.o
# $/sbin/ifconfig ra0 inet YOUR_IP up

#[kernel 2.6]
# $/sbin/insmod rt2870sta.ko
# $/sbin/ifconfig ra0 inet YOUR_IP up

7> unload driver
$/sbin/ifconfig ra0 down
$/sbin/rmmod rt2870sta

=======================================================================
CONFIGURATION:
====================
RT2870 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file

i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)modify configuration file "RT2870STA.dat" in /etc/Wireless/RT2870STA/RT2870STA.dat.

Configuration File : RT2870STA.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT2870STA/RT2870STA.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi RT2870STA.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
SSID=Dennis2860AP
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=OPEN
EncrypType=NONE
WPAPSK=
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
EthConvertMode=
EthCloneMac=
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
MeshId=MESH
MeshAutoLink=1
MeshAuthMode=OPEN
MeshEncrypType=NONE
MeshWPAKEY=
MeshDefaultkey=1
MeshWEPKEY=
CarrierDetect=0

-----------------------------------------------
*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)

All WMM parameters do not support iwpriv command but ˇĄWmmCapableˇ¦ˇ¦,
please store all parameter to RT2870STA.dat, and restart driver.

-----------------------------------------------
syntax is 'Param'='Value' and describes below.

@> CountryRegion=value
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10 ~ 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
7: use 5 ~ 13 Channel
31: use 1 ~ 14 Channel (ch1-11:active scan, ch12-14 passive scan)

@> CountryRegionABand=value
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
8: use 52, 56, 60, 64 Channel
9: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 Channel
10: use 36, 40, 44, 48, 149, 153, 157, 161, 165 Channel
11: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 Channel

@> CountryCode=value
value
AG, AR, AW, AU, AT, BS, BB, BM, BR, BE, BG, CA, KY, CL, CN, CO, CR, CY, CZ, DK, DO, EC, SV, FI, FR, DE,
GR, GU, GT, HT, HN, HK, HU, IS, IN, ID, IE, IL, IT, JP, JO, LV, LI, LT, LU, MY, MT, MA, MX, NL, NZ, NO,
PE, PT, PL, RO, RU, SA, CS, SG, SK, SI, ZA, KR, ES, SE, CH, TW, TR, GB, UA, AE, US, VE
"" => using default setting: 2.4 G - ch 1~11; 5G - ch 52~64, 100~140, 149~165

@> SSID=value
value
0~z, 1~32 ascii characters.

@> WirelessMode=value
value
0: legacy 11b/g mixed
1: legacy 11B only
2: legacy 11A only //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
3: legacy 11a/b/g mixed //Not support in RfIcType=1(id=RFIC_5225) and RfIcType=2(id=RFIC_5325)
4: legacy 11G only
5: 11ABGN mixed
6: 11N only
7: 11GN mixed
8: 11AN mixed
9: 11BGN mixed
10: 11AGN mixed

@> Channel=value
value
depends on CountryRegion or CountryRegionABand

@> BGProtection=value
value
0: Auto
1: Always on
2: Always off

@> TxPreamble=value
value
0:Preamble Long
1:Preamble Short
2:Auto

@> RTSThreshold=value
value
1~2347

@> FragThreshold=value
value
256~2346

@> TxBurst=value
value
0: Disable
1: Enable

@> NetworkType=value
value
Infra: infrastructure mode
Adhoc: adhoc mode

@> AuthMode=value
value
OPEN For open system
SHARED For shared key system
WEPAUTO Auto switch between OPEN and SHARED
WPAPSK For WPA pre-shared key (Infra)
WPA2PSK For WPA2 pre-shared key (Infra)
WPANONE For WPA pre-shared key (Adhoc)
WPA Use WPA-Supplicant
WPA2 Use WPA-Supplicant

@> EncrypType=value
value
NONE For AuthMode=OPEN
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK or WPA2PSK
AES For AuthMode=WPAPSK or WPA2PSK

@> DefaultKeyID=value
value
1~4

@> Key1=value
Key2=value
Key3=value
Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
(usage : "iwpriv" only)

@> Key1Type=vaule
Key2Type=value
Key3Type=vaule
Key4Type=vaule
value
0 hexadecimal type
1 assic type
(usage : reading profile only)

@> Key1Str=value
Key2Str=value
Key3Str=vaule
Key4Str=vaule
value
10 or 26 characters (key type=0)
5 or 13 characters (key type=1)
(usage : reading profile only)

@> WPAPSK=value
value
8~63 ASCII or
64 HEX characters

@> WmmCapable=value
value
0: Disable WMM
1: Enable WMM

@> PSMode=value
value
CAM Constantly Awake Mode
Max_PSP Max Power Savings
Fast_PSP Power Save Mode

@> FastRoaming=value
value
0 Disabled
1 Enabled

@> RoamThreshold=value
value
Positive Interger(dBm)

@> HT_RDG=value
value
0 Disabled
1 Enabled

@> HT_EXTCHA=value (Extended Channel Switch Announcement)
value
0 Below
1 Above

@> HT_OpMode=value
value
0 HT mixed format
1 HT greenfield format

@> HT_MpduDensity=value
value (based on 802.11n D2.0)
0: no restriction
1: 1/4 Łgs
2: 1/2 Łgs
3: 1 Łgs
4: 2 Łgs
5: 4 Łgs
6: 8 Łgs
7: 16 Łgs

@> HT_BW=value
value
0 20MHz
1 40MHz

@> HT_AutoBA=value
value
0 Disabled
1 Enabled

@> HT_BADecline
value
0 Disabled
1 Enabled <Reject BA request from AP>

@> HT_AMSDU=value
value
0 Disabled
1 Enabled

@> HT_BAWinSize=value
value
1 ~ 64

@> HT_GI=value
value
0 long GI
1 short GI

@> HT_MCS=value
value
0 ~ 15
33: auto

@> HT_MIMOPSMode=value
value (based on 802.11n D2.0)
0 Static SM Power Save Mode
1 Dynamic SM Power Save Mode
2 Reserved
3 SM enabled
(not fully support yet)

@> EthConvertMode=value
value
dongle
clone
hybrid

@> EthCloneMac=value
value
xx:xx:xx:xx:xx:xx

@> IEEE80211H=value
value
0 Disabled
1 Enabled

@> TGnWifiTest=value
value
0 Disabled
1 Enabled

@> WirelessEvent=value
value
0 Disabled
1 Enabled <send custom wireless event>

@> MeshId=value
value
Length 1~32 ascii characters

@> MeshAutoLink=value
value
0 Disabled
1 Enabled

@> MeshAuthMode=value
value
OPEN For open system
WPANONE For WPA pre-shared key (Adhoc)

@> MeshEncrypType=value
value
NONE For MeshAuthMode=OPEN
WEP For MeshAuthMode=OPEN
TKIP For MeshAuthMode=WPANONE
AES For MeshAuthMode=WPANONE

@> MeshWPAKEY=value
value
8~63 ASCII or
64 HEX characters

@> MeshDefaultkey=value
value
1~4

@> MeshWEPKEY=value
value
10 or 26 characters
5 or 13 characters

@> CarrierDetect=value
value
0 Disabled
1 Enabled

MORE INFORMATION
=================================================================================
If you want for rt2870 driver to auto-load at boot time:
A) choose ra0 for first RT2870 WLAN card, ra1 for second RT2870 WLAN card, etc.

B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias ra0 rt2870sta

C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0
DEVICE='ra0'
ONBOOT='yes'


NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'

*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network

=======================================================================
Dongle/Clone Features:
======================
A) Dongle mode:
Provides a 1-to-N MAC address mapping mechanism such that more than one PC behind the STA
can transparently connect to the AP.

B) Clone mode:
Provides a 1-to-1 MAC address mapping mechanism.
STA can use own MAC as SA MAC or
use user desired MAC as SA MAC or
use source MAC of first packet coming from wired device as SA MAC.
NOTE: In this mode, only the PC who own the specified MAC can connect to the AP.


C) Hybrid mode(Dongle+Clone):
Provides a 1-to-N MAC address mapping mechanism such that more than one PC behind the STA
can transparently connect to the AP.
STA can use own MAC as SA MAC or
use user desired MAC as SA MAC or
use source MAC of first packet coming from wired device as SA MAC.

D) Please refer to "Config STA to link as dongle mode..." in iwpriv_usage.txt for releated commands.

[kucmais]

iwpriv_usage.txt

iwpriv
=================
This is detailed explanation of each parameters for iwpriv.
Before reading this document, make sure you already read README.

-------------------------------------------------------------------------------------------------------
USAGE:
iwpriv ra0 commands val

NOTE:
Wireless Extension Private Handlers

where
[commands] [val]
{range}
----------------- -------------------------------------------------
wsc_conf_mode {0, 1, 2}
::Set WPS conf mode
0: WPS Disabled
1: Enrollee
2: Registrar

wsc_mode {1, 2}
::PIN or PBC
1: PIN
2: PBC

wsc_pin {00000000 ~ 99999999}
::Set Enrollee's PIN Code

wsc_ssid {0~z, 1~32 ascii characters}
::Set WPS AP SSID

wsc_start NULL
::Trigger RT2860 STA driver to do WPS process

wsc_stop NULL
::Stop WPS process

wsc_gen_pincode NULL
::Generate new PIN code

wsc_cred_count {1 ~ 8}
::Set count of WPS credential

wsc_cred_ssid {"idx ssid_str"}
::Set SSID into credtentail[idx]
idx: 0 ~ 7
ssid_str: 0~z, 1~32 ascii characters

wsc_cred_auth {"idx auth_str"}
::Set AuthMode into credtentail[idx]
idx: 0 ~ 7
auth_str: OPEN, WPAPSK, WPA2PSK, SHARED, WPA, WPA2

wsc_cred_encr {"idx encr_str"}
::Set EncrypType into credtentail[idx]
idx: 0 ~ 7
encr_str: NONE, WEP, TKIP, AES

wsc_cred_keyIdx {"idx key_index"}
::Set Key Index into credtentail[idx]
idx: 0 ~ 7
key_index: 1 ~ 4

wsc_cred_key {"idx key"}
::Set Key into credtentail[idx]
idx: 0 ~ 7
key: ASCII string (wep_key_len(=5,13), passphrase_len(=8~63))
OR
Hex string (wep_key_len(=10,26), passphrase_len(=64))

wsc_cred_mac {"idx mac_str"}
::Set AP's MAC into credtentail[idx]
idx: 0 ~ 7
mac_str: xx:xx:xx:xx:xx:xx

wsc_conn_by_idx {0 ~ 7}
::Connect AP by credential index

wsc_auto_conn {0, 1}
::Set driver to re-connecting to AP or not after registration.
0: Disabled, driver won't re-connect to AP with new configurations.
1: Enabled, driver will re-connect to AP with new configurations.

wsc_ap_band {0, 1, 2}
::Set prefer band to do WPS with dual band WPS AP
0 : prefer 2.4G
1 : prefer 5G
2 : auto
Default value is auto (2)

-------------------------------------------------------------------------------------------------------
USAGE:
iwpriv ra0 set [parameters]=[val]

NOTE:
Execute one iwpriv/set command simultaneously.

where
[parameters] [val]
{range}
----------------- -------------------------------------------------
CountryRegion {0~7}
::Set country region
0: 1 ~ 11 ch
1: 1 ~ 13 ch
2: 10, 11 ch
3: 10 ~ 13 ch
4: 14 ch
5: 1 ~ 14 ch
6: 3 ~ 9 ch
7: 5 ~ 13 ch
31: 1 ~ 14 ch (ch1-11:active scan, ch12-14 passive scan)

CountryRegionABand {0~11}
::Set country region for A band
0: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 ch
1: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch
2: 36, 40, 44, 48, 52, 56, 60, 64 ch
3: 52, 56, 60, 64, 149, 153, 157, 161 ch
4: 149, 153, 157, 161, 165 ch
5: 149, 153, 157, 161 ch
6: 36, 40, 44, 48 ch
7: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 ch
8: 52, 56, 60, 64 ch
9: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 ch
10: 36, 40, 44, 48, 149, 153, 157, 161, 165 ch
11: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 ch

SSID {0~z, 1~32 ascii characters}
::Set AP SSID

WirelessMode {0~10}
::Set Wireless Mode
0: legacy 11b/g mixed
1: legacy 11B only
2: legacy 11A only
3: legacy 11a/b/g mixed
4: legacy 11G only
5: 11ABGN mixed
6: 11N only
7: 11GN mixed
8: 11AN mixed
9: 11BGN mixed
10: 11AGN mixed

Channel depends on CountryRegion or CountryRegionForABand
::Set Channel

BGProtection {0~2}
::Set 11B/11G Protection
0:Auto,
1:Always on,
2:Always off

TxPreamble {0~2}
::Set TxPreamble
0:Preamble Long,
1:Preamble Short,
2:Auto

RTSThreshold {1~2347}
::Set RTS Threshold

FragThreshold {256~2346}
::Set Fragment Threshold

TxBurst {0,1}
::Set TxBurst Enable or Disable
0:Disable,
1:Enable

NetworkType {Infra,Adhoc}
::Set Network type

AuthMode {OPEN,SHARED,WEPAUTO,WPAPSK,WPA2PSK,WPANONE}
::Set Authentication Mode

EncrypType {NONE,WEP,TKIP,AES}
::Set Encryption Type

DefaultKeyID {1~4}
::Set Default Key ID


Key1 {5 ascii characters or 10 hex number or
13 ascii characters or 26 hex numbers}
::Set Key1 String

Key2 {5 ascii characters or 10 hex number or
13 ascii characters or 26 hex numbers}
::Set Key2 String

Key3 {5 ascii characters or 10 hex number or
13 ascii characters or 26 hex numbers}
::Set Key3 String

Key4 {5 ascii characters or 10 hex number or
13 ascii characters or 26 hex numbers}
::Set Key4 String

WPAPSK {8~63 ascii or 64 hex characters}
::WPA Pre-Shared Key

WmmCapable {0,1}
::Set WMM Capable
0:Disable WMM,
1:Enable WMM

PSMode {CAM, MAX_PSP, FAST_PSP}
::Set Power Saving Mode

HtBw {0,1}
::Set BandWidth
0: 20Hz
1: 40Hz

HtMcs {0 ~ 15, 33}
::Set MCS
33: Auto Rate

HtGi {0,1}
::Set Guard Interval(GI)
0: long GI
1: short GI

HtOpMode {0,1}
::Set HT Operation Mode
0: HT mixed format
1: HT greenfield format

HtExtcha {0,1}
::Set Extended Channel Switch Announcement
0: Below
1: Above

HtMpduDensity {0 ~ 7}
::Set The Minimum Time Between MPDUs within an AMPDU

HtBaWinSize {1 ~ 64}
::Set BA WinSize

HtRdg {0,1}
::Set RDG Capable
0: Disabled
1: Enabled

HtAmsdu {0,1}
::Set AMSDU Capable
0: Disabled
1: Enabled

HtAutoBa {0,1}
::Set Auto BA Capable
0: Disabled
1: Enabled

HtBaDecline {0,1}
::Reject BA request from AP
0: Disabled
1: Enabled

HtProtect {0,1}
::Set HT Protect Capable
0: Disabled
1: Enabled

FixedTxMode {CCK, OFDM}
:: Set Fixed Tx Mode for fixed rate setting
Mode = CCK
MCS = 0 => 1Mbps
= 1 => 2Mbps
= 2 => 5.5 Mbps
= 3 => 11 Mbps
Mode = OFDM
MCS = 0 => 6Mbps
= 1 => 9Mbps
= 2 => 12Mbps
= 3 => 18Mbps
= 4 => 24Mbps
= 5 => 36Mbps
= 6 => 48Mbps
= 7 => 54Mbps

==> Build Ethernet Convert function. Please set 'HAS_ETH_CONVERT_SUPPORT=y' in os/linux/config.mk
EthConvertMode {dongle, clone, hybrid}
::Set Ethernet Convert Mode

EthCloneMac {xx:xx:xx:xx:xx:xx}
:: Set Clone MAC

LongRetry {0,255}
:: Set Tx Long Retry Limit

ShortRetry {0,255}
:: Set Tx Short Retry Limit

MeshId {Length 1~32 ascii characters}
:: Set Mesh ID

MeshHostName {Length 1~32 ascii characters}
:: Set Mesh Host Name

MeshAutoLink {1,0}
:: Set Mesh Auto Link Capable
0: Disabled
1: Enabled

MeshAddLink {xx:xx:xx:xx:xx:xx}
:: Add Mesh Link

MeshDelLink {xx:xx:xx:xx:xx:xx}
:: Delete Mesh Link

MeshMultiCastAgeOut {20 ~ 65535 seconds}
:: Set AgeOut time for Mesh MultiCast

MeshAuthMode {OPEN, WPANONE}
:: Set Mesh Authentication Mode

MeshEncrypType {NONE, WEP, TKIP, AES}
:: Set Mesh Encryption Type

MeshDefaultkey {1 ~ 4}
:: Set Mesh Default Key ID

MeshWEPKEY {5 ascii characters or 10 hex number or
13 ascii characters or 26 hex numbers}
:: Set Mesh WEP Key String

MeshWPAKEY {8~63 ascii or 64 hex characters}
:: Set Mesh WPA Pre-Shared Key

Examples
===================================================================
-------------------------------------------------------------------------------------------------------
a> Config STA to link with AP which is OPEN/NONE(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Infra
2. iwpriv ra0 set AuthMode=OPEN
3. iwpriv ra0 set EncrypType=NONE
4. iwpriv ra0 set SSID="AP's SSID"

b> Config STA to link with AP which is SHARED/WEP(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Infra
2. iwpriv ra0 set AuthMode=SHARED
3. iwpriv ra0 set EncrypType=WEP
4. iwpriv ra0 set DefaultKeyID=1
5. iwpriv ra0 set Key1="AP's wep key"
6. iwpriv ra0 set SSID="AP's SSID"

c> Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Infra
2. iwpriv ra0 set AuthMode=WPAPSK
3. iwpriv ra0 set EncrypType=TKIP
4. iwpriv ra0 set SSID="AP's SSID"
5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"
6. iwpriv ra0 set SSID="AP's SSID"

d> Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Infra
2. iwpriv ra0 set AuthMode=WPAPSK
3. iwpriv ra0 set EncrypType=AES
4. iwpriv ra0 set SSID="AP's SSID"
5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"
6. iwpriv ra0 set SSID="AP's SSID"

e> Config STA to link with AP which is WPA2PSK/TKIP(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Infra
2. iwpriv ra0 set AuthMode=WPA2PSK
3. iwpriv ra0 set EncrypType=TKIP
4. iwpriv ra0 set SSID="AP's SSID"
5. iwpriv ra0 set WPAPSK=12345678
6. iwpriv ra0 set SSID="AP's SSID"

f> Config STA to create/link as adhoc mode, which is OPEN/NONE(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Adhoc
2. iwpriv ra0 set AuthMode=OPEN
3. iwpriv ra0 set EncrypType=NONE
4. iwpriv ra0 set SSID="Adhoc's SSID"

g> Config STA to create/link as adhoc mode, which is WPANONE/TKIP(Authentication/Encryption)
1. iwpriv ra0 set NetworkType=Adhoc
2. iwpriv ra0 set AuthMode=WPANONE
3. iwpriv ra0 set EncrypType=TKIP
4. iwpriv ra0 set SSID="AP's SSID"
5. iwpriv ra0 set WPAPSK=12345678
6. iwpriv ra0 set SSID="AP's SSID"

h> Get site survey
usage: iwpriv ra0 get_site_survey

i> Get Statistics
usage: iwpriv ra0 stat ; read statistic counter
iwpriv ra0 set ResetCounter=0 ; reset statistic counter

j> Link with an AP which is the largest strength ; set ANY SSID (ssidLen=0)
usage: iwconfig ra0 essid ""
or
usage: iwpriv ra0 set SSID=""

k> Config STA to link as dongle mode with STA own MAC
usage: iwpriv ra0 set EthConvertMode=dongle

l> Config STA to link as clone mode
usage: iwpriv ra0 set EthConvertMode=clone
iwpriv ra0 set EthCloneMac="Desired MAC" ;; 00:00:00:00:00:00 means using STA own MAC
;; FF:FF:FF:FF:FF:FF means using source MAC of first packet coming from wired device

m> Config STA to link as hybrid(dongle+clone) mode
usage: iwpriv ra0 set EthConvertMode=hybrid
iwpriv ra0 set EthCloneMac="Desired MAC" ;; 00:00:00:00:00:00 means using STA own MAC
;; FF:FF:FF:FF:FF:FF means using source MAC of first packet coming from wired device

===================================================================

iwlist
=================
This is detailed explanation of each parameters for iwlist.

-------------------------------------------------------------------------------------------------------
iwlist ra0 scanning ; list the results after scanning(manual rescan)



=======================================================================================================

iwconfig
=================
The following are our support in standard configuration - iwconfig

-------------------------------------------------------------------------------------------------------
iwconfig ra0 essid {NN|on|off} ; set essid
iwconfig ra0 mode {managed|ad-hoc|...} ; set wireless mode
>> rt2860sta driver support monitor mode with linux kernel > 2.4.20.
>> Note: For using monitor mode => if mesh interface is ON, please down the mesh interface first.
iwconfig ra0 freq N.NNNN[k|M|G]] ; set frequency
iwconfig ra0 channel N ; set channel
iwconfig ra0 ap {N|off|auto} ; set AP address
iwconfig ra0 nick N ; set nickname
iwconfig ra0 rate {N|auto|fixed} ; set rate (only support legacy rate setting)
iwconfig ra0 rts {N|auto|fixed|off} ; set RTS threshold
iwconfig ra0 frag {N|auto|fixed|off} ; set Fragment threshold
iwconfig ra0 enc {NNNN-NNNN|off} ; set encryption type
iwconfig ra0 power {period N|timeout N} ; set power management modes

*** Wireless extension usage please refer to man page of 'iwconfig', 'iwlist' and 'iwpriv'. ***

[kucmais]

sta_ate_iwpriv_usage.txt

===================================================================================================
ATE Test Command Format for station driver

****** IMPORTANT ******
If you are not familiar with hardware, it is recommanded not to modify hardware default value.
It may damage hardware.

===================================================================================================
Usage:
iwpriv ra0 [act] [parameters]=[val]


where

[act] [parameters] [val] constraints explaination
----- ------------- ----------------- --------------------------------

=====================================
1. Set ATE actions.
Value:
ATESTART - Start ATE function and stop station function.
ATESTOP - Stop ATE function and start station function.
TXCONT - Start continuous TX, for power mask.
TXCARR - Start carrier test, for frequency calibration.
TXFRAME - Transmit frame, for EVM.
RXFRAME - Continuous RX, for PER/FER.

1.1 ATEDA
Set ATE frame header destination address.
Value:
xx:xx:xx:xx:xx:xx ; hex

1.2 ATESA
Set ATE frame header source addr.
Value:
xx:xx:xx:xx:xx:xx ; hex

1.3 ATEBSSID
Set ATE frame header BSSID.
Value:
xx:xx:xx:xx:xx:xx ; hex

1.4 ATECHANNEL
Set ATE Channel, deimal.
Value:
802.11b/g: 1 ~ 14 depends on CountryRegion setting

1.5 ATETXPOW0
Set ATE Tx power for Antenna 1.
Value:
0 ~ 31 ; 2.4GHz, deimal
-7 ~15 ; 5.5GHz, deimal

1.6 ATETXPOW1
Set ATE Tx power for Antenna 2.
Value:
0 ~ 31 ; 2.4GHz, decimal
-7 ~15 ; 5.5GHz, deimal

1.7 ATETXFREQOFFSET
Set ATE RF frequency offset.
Value:
0 ~ 63 ; unit: 2KHz, decimal

1.8 ATETXLEN
Set ATE frame length.
Value:
24 ~ 2312 ; decimal

1.9 ATETXCNT
Set ATE frame Tx count.
Value:
1 ~ ; 32-bit, decimal

1.10 ATETXMODE (Refer to TxMode)
Set ATE Tx Mode.
Value:
0: CCK 802.11b
1: OFDM 802.11g
2: HT_MIX 802.11b/g/n
3: Green Field 802.11n

1.11 ATETXBW (Refer to TxMode)
Set ATE Tx and Rx Bandwidth.
Value:
0: 20MHz
1: 40MHz

1.12 ATETXGI (Refer to TxMode)
Set ATE Tx Guard Interval.
Value:
0: Long
1: Short

1.13 ATETXMCS (Refer to TxMode)
Set ATE Tx MCS type.
Value:
0 ~ 15

1.14 ATETXANT
Set ATE TX antenna.
Value:
0: All
1: Antenna one
2: Antenna two

1.15 ATERXANT
Set ATE RX antenna.
Value:
0: All
1: Antenna one
2: Antenna two
3: Antenna three

1.16 ATERXFER
Set ATE to periodically reset and show up RxCount (per-second) and RxTotalCount.
Value:
0: Disable counter visability
1: Enable counter visability

1.17 ATESHOW
Show all parameters of ATE.
Value:
1

1.18 ATEHELP
List all commands of ATE.
Value:
1

1.19 ResetCounter
Reset statistic counter.
Value:
1

1.20 ATERRF
Read all of the RF registers.
Value:
1

1.21 ATEWRF1
Write the RF register 1.
Value:
xxxxxxxx ;32-bit, hex

1.22 ATEWRF2
Write the RF register 2.
Value:
xxxxxxxx ;32-bit, hex

1.23 ATEWRF3
Write the RF register 3.
Value:
xxxxxxxx ;32-bit, hex

1.24 ATEWRF4
Write the RF register 4.
Value:
xxxxxxxx ;32-bit, hex

1.25 ATELDE2P
Overwrite all EEPROM contents
Value:
1
E.g.
iwpriv ra0 set ATELDE2P=1

1.26 ATERE2P
Display all EEPROM content.
Value:
1
E.g.
iwpriv ra0 set ATERE2P=1

===================================================================================================
2. Examples:
=========

2.1 Check EVM & Power
iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATEDA=00:11:22:33:44:55
iwpriv ra0 set ATESA=00:aa:bb:cc:dd:ee
iwpriv ra0 set ATEBSSID=00:11:22:33:44:55
iwpriv ra0 set ATECHANNEL=1 ; set Channel
iwpriv ra0 set ATETXMODE=1 ; set TX-Mode.
iwpriv ra0 set ATETXMCS=7 ; set MCS type.
iwpriv ra0 set ATETXBW=0 ; set Bandwidth
iwpriv ra0 set ATETXGI=0 ; set Long GI.
iwpriv ra0 set ATETXLEN=1024 ; set packet length.
iwpriv ra0 set ATETXPOW0=18
iwpriv ra0 set ATETXPOW1=18
iwpriv ra0 set ATETXCNT=100000
iwpriv ra0 set ATE=TXFRAME
ˇK
iwpriv ra0 set ATETXPOW0=19
ˇK
iwpriv ra0 set ATETXPOW0=20
ˇK
iwpriv ra0 set ATE=ATESTART

2.2 Check Carrier
iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATECHANNEL=1 ; set Channel
iwpriv ra0 set ATETXMODE=1 ; set TX-Mode.
iwpriv ra0 set ATETXMCS=7 ; set MCS type.
iwpriv ra0 set ATETXBW=0 ; set Bandwidth
iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial)
iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame(inform BBP to change, modulation mode)
iwpriv ra0 set ATE=TXCARR ; Start Tx carrier, Measure carrier with instrument
iwpriv ra0 set ATETXPOW0=05
iwpriv ra0 set ATETXPOW1=05
iwpriv ra0 set ATETXFREQOFFSET=19
iwpriv ra0 set ATE=ATESTART

2.3 Check specturm mask
iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATECHANNEL=1 ; set Channel
iwpriv ra0 set ATETXMODE=1 ; set TX-Mode.
iwpriv ra0 set ATETXMCS=7 ; set MCS type.
iwpriv ra0 set ATETXBW=0 ; set Bandwidth
iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial)
iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame(inform BBP to change, modulation mode)
iwpriv ra0 set ATE=TXCONT ; Start continuous TX, Measure specturm mask with instrument
iwpriv ra0 set ATETXPOW0=5
iwpriv ra0 set ATETXPOW1=5
iwpriv ra0 set ATE=ATESTART

2.4 Frequency offset tuning
iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATECHANNEL=1 ; set Channel
iwpriv ra0 set ATETXMODE=1 ; set TX-Mode.
iwpriv ra0 set ATETXMCS=7 ; set MCS type.
iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial)
iwpriv ra0 set ATETXFREQOFFSET=0 ; Set frequency offset 0(decimal)
iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame
iwpriv ra0 set ATE=TXCARR ; Start Tx carrier, Measure carrier frequency with instrument
iwpriv ra0 set ATETXFREQOFFSET=10 ; Dynamic turning frequency offset, 10(decimal)
iwpriv ra0 set ATETXFREQOFFSET=20 ; Dynamic turning frequency offset, 20(decimal)
iwpriv ra0 set ATE=ATESTART ; Stop, Store the tuning result to EEPROM

2.5 Rx
iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATECHANNEL=1 ; set Channel
iwpriv ra0 set ResetCounter=1 ; Reset statistic counter
iwpriv ra0 set ATETXFREQOFFSET=value ;To use the ˇ§valueˇ¨(decimal) you got in tx calibration
iwpriv ra0 set ATETXMODE=1 ; set TX-Mode.
iwpriv ra0 set ATETXMCS=7 ; set MCS type.
iwpriv ra0 set ATETXBW=0 ; set Bandwidth
iwpriv ra0 set ATE=RXFRAME ; Start Rx,
iwpriv ra0 set ATERXFER=1 ; show RxCnt and RSSI/per-antenna, Transmit test packets
iwpriv ra0 set ATE=ATESTART ; Stop
iwpriv ra0 stat ; get statistics counter
iwpriv ra0 set ATERXFER=1
iwpriv ra0 set ATERXANT=1

iwpriv ra0 set ATE=ATESTART
iwpriv ra0 set ATERXANT=0
iwpriv ra0 set ATE=RXFRAME

2.6 Show all ate parameters
iwpriv ra0 set ATESHOW=1

Mode=4
TxPower0=0
TxPower1=0
TxAntennaSel=0
RxAntennaSel=0
BBPCurrentBW=0
GI=0
MCS=7
TxMode=1
Addr1=00:11:22:aa:bb:cc
Addr2=00:11:22:aa:bb:cc
Addr3=00:11:22:aa:bb:cc
Channel=1
TxLength=1024
TxCount=40000
TxRate=11
RFFreqOffset=0

2.7 Online help
iwpriv ra0 set ATEHELP=1

ATE=ATESTART, ATESTOP, TXCONT, TXCARR, TXFRAME, RXFRAME
ATEDA
ATESA
ATEBSSID
ATECHANNEL, range:0~14(unless A band !).
ATETXPOW0, set power level of antenna 1.
ATETXPOW1, set power level of antenna 2.
ATETXANT, set TX antenna. 0: all, 1: antenna one, 2: antenna two.
ATERXANT, set RX antenna.0: all, 1: antenna one, 2: antenna two, 3: antenna three.
ATETXFREQOFFSET, set frequency offset, range 0~63.
ATETXBW, set BandWidth, 0:20MHz, 1:40MHz.
ATETXLEN, set Frame length, range 24~2312.
ATETXCNT, set how many frame going to transmit.
ATETXMCS, set MCS, reference to rate table.
ATETXMODE, set Mode 0: CCK, 1: OFDM, 2: HT-Mix, 3: GreenField, reference to rate table.
ATETXGI, set GI interval, 0: Long, 1: Short.
ATERXFER, 0: disable Rx Frame error rate. 1: enable Rx Frame error rate.
ATERRF, show all RF registers.
ATEWRF1, set RF1 register.
ATEWRF2, set RF2 register.
ATEWRF3, set RF3 register.
ATEWRF4, set RF4 register.
ATELDE2P, load EEPROM from .bin file.
ATERE2P, display all EEPROM content.
ATESHOW, display all parameters of ATE.
ATEHELP, online help.

2.8 Display Rx Packet Count and RSSI
iwpriv ra0 set ATERXANT=0 ==> Enable All Three Rx Antennas
iwpriv ra0 set ATERXFER=1 ==> Enable Rx Frame Error Rate: RxCnt/RxTotal
iwpriv ra0 set ATE=RXFRAME ==> Start Rx
MlmePeriodicExec: Rx packet cnt = 2/4
MlmePeriodicExec: Rx AvgRssi0=-88, AvgRssi1=-80, AvgRssi2=-91
MlmePeriodicExec: Rx packet cnt = 2/6
MlmePeriodicExec: Rx AvgRssi0=-86, AvgRssi1=-77, AvgRssi2=-89ˇK
ˇK

iwpriv ra0 set ATERXANT=1 ==> Enable Three Rx Antenna-1
iwpriv ra0 set ATERXFER=1 ==> Enable Rx Frame Error Rate: RxCnt/RxTotal
iwpriv ra0 set ATE=RXFRAME ==> Start Rx
MlmePeriodicExec: Rx packet cnt = 0/7
MlmePeriodicExec: Rx AvgRssi=-87
MlmePeriodicExec: Rx packet cnt = 7/14
MlmePeriodicExec: Rx AvgRssi=-90
ˇK
ˇK


===================================================================================================
3. Hardware Access
==================

=====================================
3.1 iwpriv ra0 bbp [parameters]=[Value]
Read/Write BBP registers by ID number.
BBPID

3.1.1 Read BBP register, BBPID only, no ˇ§=ˇ¨ symbol.
BBPID:
0 ~ xx ; decimal, 8-bit
BBPID=Value

3.1.2 Write BBP register.
BBPID:
0 ~ xx ; decimal, 8-bit
Value:
00 ~FF ; hexdecimal, 8-bit

=====================================
3.2 iwpriv ra0 mac [parameters]=[val]
Read/Write MAC registers by offset.
MAC_OFFSET

3.2.1 Read MAC register, MAC_OFFSET only, no ˇ§=ˇ¨ symbol.
MAC_OFFSET:
0000 ~ FFFF ; hexdecimal, 16-bit
MAC_OFFSET=Value

3.2.2 Write MAC register.
MAC_OFFSET:
0000 ~ FFFF ; hexdecimal, 16-bit
Value:
0000 ~FFFF ; hexdecimal, 32-bit

=====================================
3.3 iwpriv ra0 e2p [parameters]=[val]
Read/Write EEPROM content by address.
EEP_ADDR

3.3.1 Read EEPROM content, EEP_ADDR only, no ˇ§=ˇ¨ symbol.
EEP_ADDR:
00 ~ FF ; hexdecimal, 16-bit alignment (0, 2, 4, 6, 8, A, C, ˇK)
EEP_ADDR=Value

3.3.2 Write EEPROM content.
EEP_ADDR:
00 ~ FF ; hexdecimal, 16-bit alignment (0, 2, 4, 6, 8, A, C, ˇK)
Value:
0000 ~FFFF ; hexdecimal, 16-bit

=====================================
3.4 Example

3.4.1 Hardware access
iwpriv ra0 bbp 0 # read BBP register 0
iwpriv ra0 bbp 0=12 # write BBP register 0 as 0x12
iwpriv ra0 mac 0 # read MAC register 0
iwpriv ra0 mac 0=1234abcd # write MAC register 0 as 0x1234abcd
iwpriv ra0 e2p 0 # read E2PROM 0
iwpriv ra0 e2p c=12ab # write E2PROM 0xc as 0x12ab

3.4.2 Statistic counter operation
iwpriv ra0 stat # read statistic counter
iwpriv ra0 set ResetCounter=0 # reset statistic counter

Suggestion:
1. To turn on ATE functionality, you have to add compile flag "RALINK_ATE" to Makefile
2. Before doing ATE testing, please stop AP function
3. If you want to test another ATE action, prefer to stop AP & ATE function
4. All ATE function settings will lose efficacy after reboot.
5. Before hardware register access, please reference hardware spec.
Note.
In ATE mode, the channel must set via "ATECHANNEL"

===================================================================================================
4. ated
=======
4.1 Introduction
The ated is an optional user space component for RT28xx Linux driver.
When Windows GUI starts, AP enters ATE mode (i.e.,ATESTART) immediately.
It behaves as a proxy between Windows GUI and RT28xx Linux driver when ATE process proceeds.
The ated will be killed automatically when Windows GUI is closed.
You can kill it manually, too(for example, type '$killall ated').
RT28xx linux driver will leave ATE mode either ated is killed or Windows GUI is closed.

4.2 Environment setup
1. Connect the platform you want to test directly with a Windows host by ether network line.
2. In the Windows host, run WinPcap_4_0.exe for the QA GUI or ./RT2880_ATE/RaUI.exe(please unrar "RT2880_ATE.rar" to get it).

4.3 How to use ated for ATE purpose
0. First you should set both "HAS_ATE=y" and "HAS_QA_SUPPORT=y" in the file ~/Module/os/linux/config.mk and compile the driver.
1. Modify the Makefile according to our target "PLATFORM".
2. Change the path of "CROSS_COMPILE" if needed.
3. Then type 'make' command to compile the source code of the daemon.
4. After the driver interface has started up, attach both of the wireless interface and the ethernet interface to the bridge interface.
5. If you have no bridge interface, please give an IP address to the ethernet interface.
(for example : '$ated -beth0')
6. After the interfaces have entered forwarding states, manually start ated, type '$ated -bbrX -iraX'.
7. If your WLAN interface and Bridge interface is "ra0" and "br0" respectively, just type $ated.
(For further usage of options, type $ated -h)
8. In the Windows host, run RT28xxQA_ATE.exe or ./RT2880_ATE/RaUI.exe.
9. Select the wired network adapter, then press OK and wait for a moment.
10.If the Windows host cannot tolerate such a broadcast storm from ated,
please run ated with option -u.(for example : '$ated -ira1 -u')
11.If your target platform concerns its network security, please run RT28xxQA_unicast.exe instead of RT28xxQA_ATE.exe.

Note :
a. The names of WLAN interface(default is "ra0") and Bridge interface(default is "br0") must be specified manually(for example : '$ated -bbr1 -ira2') if your WLAN interface or Bridge interface is not "ra0" or "br0" respectively !
b. Please make sure no other RaUI is running before you excute ./RT2880_ATE/RaUI.exe.

[West]

Stacilo dat odkaz na miesto odkial si stiahol ovladac.
Este poprosim vypis prikazu 'lsmod | grep rt"
Tym by sa zistilo, ci system k wifi hardwaru (ktory detekoval spravne) automaticky nacital aj ovladac.

[kucmais]

Omlouvám se za to vložení, ale já ovladač nestahoval dostal jsem ho na cd spolu s přijmačem,
výpis lsmod
gameport 16384 1 snd_ens1371
parport_pc 32768 1
parport 40960 3 lp,ppdev,parport_pc

[West]

Vyzera to tak, ze jadro systemu, ktore tam mas teraz neobsahuje ovladac pre tvoj wifi adapter, inak by tam sa tam objavilo nieco ako rt2800usb. Dufam, ze si ten prikaz spustal vtedy ked si mal v pocitaci zasunuty wifi adapter. Doporucujem aktualizovat system ak mas taku moznost.
System nahrany z CD ma este starsie jadro kde ten ovladac neni. Aktualizovany system Mint 17.3 by mal mat jadro verzie 4.4. Aku verziu jadra mas teraz si mozes pozriet prikazom 'uname -a'.
Podla nasledujucej stranky by jadro malo obsahovat ovladac pre tvoj adapter od verzie 4.2
https://wikidevi.com/wiki/List_of_Wi-Fi ... s_in_Linux
Na tej stranke najdes svoj adapter pod identifikatorom 148f_7601
Takto by si to mal jednoduchsie ako s kompilaciou ovladaca, ktora nieje zrovna najjednoduchsia.
Ak to nezvladnes budeme pokracovat kompilaciou. Nieje to celkom trivialna zalezitost, pretoze tento konkretny ovladac je potrebne spravne predpripravit pred kompilaciou.

[kucmais]

je tam dle toho co jsem pochopil jadro 4,1 pokud oujde aktualizovat pomocí usb disku tak jo.
tak jsem nikde nenašel jak aktualizovat jádro bez internetu.