satapouch píše:Pokud používáš nvidia-current, tak dle mě musí být "Driver=nvidia-current". Jinak změnit je právě nutné druh ovladače v Bumlebee.conf. Navíc, je potřeba mít instalován i Primus.
Driver=nvidia-current nepomohlo, předtím jsem primus neinstaloval a není mi jasné, pokud ho to potřebuje, proč si ho to nenatáhlo v závislostech?? Každopádně zkouším a ejhle:
Kód: Vybrat vše
sonic@notebook ~ $ sudo apt-get install primus
Čtu seznamy balíků... Hotovo
Vytvářím strom závislostí
Čtu stavové informace... Hotovo
Balík primus není dostupný, ale jiný balík se na něj odkazuje.
To může znamenat že balík chybí, byl zastarán, nebo je dostupný
pouze z jiného zdroje
E: Balík „primus“ nemá kandidáta pro instalaci
sonic@notebook ~ $
Přitom mám přidaný repo
ppa:bumblebee/stable a nic. Pro sichr přidávám ještě výpis souboru
bumlebee.conf:
Kód: Vybrat vše
sonic@notebook /etc/bumblebee $ cat bumblebee.conf
# Configuration file for Bumblebee. Values should **not** be put between quotes
## Server options. Any change made in this section will need a server restart
# to take effect.
[bumblebeed]
# The secondary Xorg server DISPLAY number
VirtualDisplay=:8
# Should the unused Xorg server be kept running? Set this to true if waiting
# for X to be ready is too long and don't need power management at all.
KeepUnusedXServer=false
# The name of the Bumbleblee server group name (GID name)
ServerGroup=bumblebee
# Card power state at exit. Set to false if the card shoud be ON when Bumblebee
# server exits.
TurnCardOffAtExit=false
# The default behavior of '-f' option on optirun. If set to "true", '-f' will
# be ignored.
NoEcoModeOverride=false
# The Driver used by Bumblebee server. If this value is not set (or empty),
# auto-detection is performed. The available drivers are nvidia and nouveau
# (See also the driver-specific sections below)
Driver=nvidia-current
## Client options. Will take effect on the next optirun executed.
[optirun]
# Acceleration/ rendering bridge, possible values are auto, virtualgl and
# primus.
Bridge=auto
# The method used for VirtualGL to transport frames between X servers.
# Possible values are proxy, jpeg, rgb, xv and yuv.
VGLTransport=proxy
# Should the program run under optirun even if Bumblebee server or nvidia card
# is not available?
AllowFallbackToIGC=false
# Driver-specific settings are grouped under [driver-NAME]. The sections are
# parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto-
# detection resolves to NAME).
# PMMethod: method to use for saving power by disabling the nvidia card, valid
# values are: auto - automatically detect which PM method to use
# bbswitch - new in BB 3, recommended if available
# switcheroo - vga_switcheroo method, use at your own risk
# none - disable PM completely
# https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods
## Section with nvidia driver specific options, only parsed if Driver=nvidia
[driver-nvidia]
# Module name to load, defaults to Driver if empty or unset
KernelDriver=nvidia-current
PMMethod=auto
# colon-separated path to the nvidia libraries
LibraryPath=/usr/lib/nvidia-current:/usr/lib32/nvidia-current
# comma-separated path of the directory containing nvidia_drv.so and the
# default Xorg modules path
XorgModulePath=/usr/lib/nvidia-current/xorg,/usr/lib/xorg/modules
XorgConfFile=/etc/bumblebee/xorg.conf.nvidia
## Section with nouveau driver specific options, only parsed if Driver=nouveau
[driver-nouveau]
KernelDriver=nouveau
PMMethod=auto
XorgConfFile=/etc/bumblebee/xorg.conf.nouveau
sonic@notebook /etc/bumblebee $
Je mi docela divné, že nemá stejný problém víc lidí?