Dobrý deň.
Chcel by som použiť starý PC s Core2Duo a SIS chipset... PC bude bez monitoru, pôjde na ňom len jedna aplikácia a na tento účel stačí.
Ide o to že zatiaľ sa mi podarilo to rozchodiť len ak spustím LIVE s režimom kompatibility. Takto mi to funguje v poriadku.
Inak systém nenabehne (obraz je biely s farebnými bodmi). Skúšal som rôzne distribúcie, rôzne verzie ale nič. Teda ak nemyslím veľmi staré verzie, kde sa ešte so SIS chipsetom rátalo....
Je možnosť ako nainštalovať a potom spúšťať Mint v režime kompatibility????
Ďakujem....
SIS chipset
Re: SIS chipset
.
Ta moznost tu urcite je.
Mohol by si v tom LIVE s režimom kompatibility
do terminalu zadat
Kód: Vybrat vše
dmesg
.
.
Re: SIS chipset
SiS se nedavno podrobneji resil bud tady nebo vedle na Ubu foru. Zkus trochu pohledat - ja uz dneska nemam silu ...
Zvuky jsou mantrami a myšlenky moudrostí, prostě proto, že se mohou objevovat ...
Re: SIS chipset
Kód: Vybrat vše
mint@mint:~$ dmesg
[ 0.000000] Linux version 5.0.0-32-generic (buildd@lgw01-amd64-015) (gcc version 7.4.0 (Ubuntu 7.4.0-1ubuntu1~18.04.1)) #34~18.04.2-Ubuntu SMP Thu Oct 10 10:36:02 UTC 2019 (Ubuntu 5.0.0-32.34~18.04.2-generic 5.0.21)
[ 0.000000] Command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/linuxmint.seed boot=casper xforcevesa nomodeset b43.blacklist=yes initrd=/casper/initrd.lz ramdisk_size=1048576 root=/dev/ram rw noapic noacpi nosplash irqpoll --
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Hygon HygonGenuine
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: x87 FPU will use FXSAVE
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007ffeffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007fff0000-0x000000007fff2fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007fff3000-0x000000007fffffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Acer ASSA90/APS290 /F671CR , BIOS R01-C0 07/04/2007
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 2400.156 MHz processor
[ 0.007433] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.007435] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.007441] last_pfn = 0x7fff0 max_arch_pfn = 0x400000000
[ 0.007455] MTRR default type: uncachable
[ 0.007456] MTRR fixed ranges enabled:
[ 0.007458] 00000-9FFFF write-back
[ 0.007459] A0000-BFFFF uncachable
[ 0.007460] C0000-CEFFF write-protect
[ 0.007461] CF000-EFFFF uncachable
[ 0.007462] F0000-FFFFF write-through
[ 0.007463] MTRR variable ranges enabled:
[ 0.007464] 0 base 000000000 mask F80000000 write-back
[ 0.007465] 1 disabled
[ 0.007466] 2 disabled
[ 0.007467] 3 disabled
[ 0.007467] 4 disabled
[ 0.007468] 5 disabled
[ 0.007469] 6 disabled
[ 0.007469] 7 disabled
[ 0.012065] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.017387] found SMP MP-table at [mem 0x000f3b70-0x000f3b7f]
[ 0.062531] check: Scanning 1 areas for low memory corruption
[ 0.062542] BRK [0x3fc01000, 0x3fc01fff] PGTABLE
[ 0.062544] BRK [0x3fc02000, 0x3fc02fff] PGTABLE
[ 0.062546] BRK [0x3fc03000, 0x3fc03fff] PGTABLE
[ 0.062594] BRK [0x3fc04000, 0x3fc04fff] PGTABLE
[ 0.062597] BRK [0x3fc05000, 0x3fc05fff] PGTABLE
[ 0.062762] BRK [0x3fc06000, 0x3fc06fff] PGTABLE
[ 0.062792] RAMDISK: [mem 0x7da36000-0x7ffeffff]
[ 0.062801] ACPI: Early table checksum verification disabled
[ 0.083661] ACPI: RSDP 0x00000000000F7CC0 000014 (v00 ACRSYS)
[ 0.083665] ACPI: RSDT 0x000000007FFF3040 000044 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.083673] ACPI: FACP 0x000000007FFF30C0 000074 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.083682] ACPI: DSDT 0x000000007FFF3180 003D7E (v01 ACRSYS AWRDACPI 00001000 MSFT 03000000)
[ 0.083686] ACPI: FACS 0x000000007FFF0000 000040
[ 0.083690] ACPI: HPET 0x000000007FFF7040 000038 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000098)
[ 0.083695] ACPI: SLIC 0x000000007FFF70C0 000176 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000020)
[ 0.083700] ACPI: _WDT 0x000000007FFF7280 000047 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.083704] ACPI: MCFG 0x000000007FFF7340 00003C (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.083709] ACPI: APIC 0x000000007FFF6F40 000084 (v01 ACRSYS ACRPRDCT 42302E31 AWRD 00000000)
[ 0.083713] ACPI: SSDT 0x000000007FFF73C0 00015C (v01 PmRef Cpu0Ist 00003000 INTL 20041203)
[ 0.083718] ACPI: SSDT 0x000000007FFF7850 0002F1 (v01 PmRef CpuPm 00003000 INTL 20040311)
[ 0.083733] ACPI: Local APIC address 0xfee00000
[ 0.083848] No NUMA configuration found
[ 0.083850] Faking a node at [mem 0x0000000000000000-0x000000007ffeffff]
[ 0.083864] NODE_DATA(0) allocated [mem 0x7da0b000-0x7da35fff]
[ 0.084208] Zone ranges:
[ 0.084209] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.084212] DMA32 [mem 0x0000000001000000-0x000000007ffeffff]
[ 0.084213] Normal empty
[ 0.084215] Device empty
[ 0.084216] Movable zone start for each node
[ 0.084220] Early memory node ranges
[ 0.084221] node 0: [mem 0x0000000000001000-0x000000000009efff]
[ 0.084223] node 0: [mem 0x0000000000100000-0x000000007ffeffff]
[ 0.084227] Zeroed struct page in unavailable ranges: 98 pages
[ 0.084228] Initmem setup node 0 [mem 0x0000000000001000-0x000000007ffeffff]
[ 0.084231] On node 0 totalpages: 524174
[ 0.084232] DMA zone: 64 pages used for memmap
[ 0.084233] DMA zone: 21 pages reserved
[ 0.084234] DMA zone: 3998 pages, LIFO batch:0
[ 0.084368] DMA32 zone: 8128 pages used for memmap
[ 0.084369] DMA32 zone: 520176 pages, LIFO batch:63
[ 0.126005] ACPI: PM-Timer IO Port: 0x1008
[ 0.126015] ACPI: Local APIC address 0xfee00000
[ 0.126036] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.126038] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.126040] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.126041] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.126044] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.126046] Using ACPI for processor (LAPIC) configuration information
[ 0.126050] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
[ 0.126065] Intel MultiProcessor Specification v1.4
[ 0.126071] MPTABLE: OEM ID: OEM00000
[ 0.126072] MPTABLE: Product ID: PROD00000000
[ 0.126073] MPTABLE: APIC at: 0xFEE00000
[ 0.126085] IOAPIC[0]: apic_id 4, version 20, address 0xfec00000, GSI 0-23
[ 0.126087] Processors: 2
[ 0.126092] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.126120] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.126122] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[ 0.126123] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.126124] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.126129] [mem 0x80000000-0xdfffffff] available for PCI devices
[ 0.126131] Booting paravirtualized kernel on bare hardware
[ 0.126140] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.126171] random: get_random_bytes called from start_kernel+0x97/0x516 with crng_init=0
[ 0.126184] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.128273] percpu: Embedded 47 pages/cpu s155648 r8192 d28672 u524288
[ 0.128286] pcpu-alloc: s155648 r8192 d28672 u524288 alloc=1*2097152
[ 0.128288] pcpu-alloc: [0] 0 1 2 3
[ 0.128338] Built 1 zonelists, mobility grouping on. Total pages: 515961
[ 0.128340] Policy zone: DMA32
[ 0.128346] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/linuxmint.seed boot=casper xforcevesa nomodeset b43.blacklist=yes initrd=/casper/initrd.lz ramdisk_size=1048576 root=/dev/ram rw noapic noacpi nosplash irqpoll --
[ 0.128548] You have booted with nomodeset. This means your GPU drivers are DISABLED
[ 0.128549] Any video related functionality will be severely degraded, and you may not even be able to suspend the system properly
[ 0.128551] Unless you actually understand what nomodeset does, you should reboot without enabling it
[ 0.128747] Misrouted IRQ fixup and polling support enabled
[ 0.128748] This may significantly impact system performance
[ 0.128864] Calgary: detecting Calgary via BIOS EBDA area
[ 0.128866] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.177112] Memory: 1989388K/2096696K available (14339K kernel code, 2335K rwdata, 4408K rodata, 2588K init, 5192K bss, 107308K reserved, 0K cma-reserved)
[ 0.177408] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.177436] Kernel/User page tables isolation: enabled
[ 0.177510] ftrace: allocating 41617 entries in 163 pages
[ 0.205329] rcu: Hierarchical RCU implementation.
[ 0.205334] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[ 0.205336] Tasks RCU enabled.
[ 0.205338] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.205340] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.209458] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16
[ 0.214315] Console: colour VGA+ 80x25
[ 0.219169] printk: console [tty0] enabled
[ 0.219250] ACPI: Core revision 20181213
[ 0.219415] ACPI: setting ELCR to 0200 (from 8e20)
[ 0.219561] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.219635] hpet clockevent registered
[ 0.219639] APIC: Switch to symmetric I/O mode setup
[ 0.219687] Not enabling interrupt remapping due to skipped IO-APIC setup
[ 0.219746] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2298cb07e2a, max_idle_ns: 440795294045 ns
[ 0.219830] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.31 BogoMIPS (lpj=9600624)
[ 0.219896] pid_max: default: 32768 minimum: 301
[ 0.219993] LSM: Security Framework initializing
[ 0.220060] Yama: becoming mindful.
[ 0.220138] AppArmor: AppArmor initialized
[ 0.221727] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.222833] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.222939] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.223020] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.223616] mce: CPU0: Thermal monitoring enabled (TM2)
[ 0.223842] process: using mwait in idle threads
[ 0.223900] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[ 0.223949] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
[ 0.224001] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.224065] Spectre V2 : Mitigation: Full generic retpoline
[ 0.224115] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.224177] Speculative Store Bypass: Vulnerable
[ 0.224268] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[ 0.224563] Freeing SMP alternatives memory: 36K
[ 0.336533] smpboot: CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (family: 0x6, model: 0xf, stepping: 0x6)
[ 0.336811] Performance Events: PEBS fmt0-, Core2 events, 4-deep LBR, Intel PMU driver.
[ 0.336881] core: PEBS disabled due to CPU errata
[ 0.336932] ... version: 2
[ 0.336979] ... bit width: 40
[ 0.337027] ... generic registers: 2
[ 0.337075] ... value mask: 000000ffffffffff
[ 0.337124] ... max period: 000000007fffffff
[ 0.337173] ... fixed-purpose events: 3
[ 0.337220] ... event mask: 0000000700000003
[ 0.337334] rcu: Hierarchical SRCU implementation.
[ 0.339037] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.339183] smp: Bringing up secondary CPUs ...
[ 0.339416] x86: Booting SMP configuration:
[ 0.339466] .... node #0, CPUs: #1
[ 0.339925] smp: Brought up 1 node, 2 CPUs
[ 0.339925] smpboot: Max logical packages: 2
[ 0.339974] smpboot: Total of 2 processors activated (9600.62 BogoMIPS)
[ 0.344121] devtmpfs: initialized
[ 0.344121] x86/mm: Memory block size: 128MB
[ 0.344543] PM: Registering ACPI NVS region [mem 0x7fff0000-0x7fff2fff] (12288 bytes)
[ 0.344543] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.344543] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.344543] pinctrl core: initialized pinctrl subsystem
[ 0.344543] RTC time: 06:51:07, date: 2020-04-21
[ 0.344543] NET: Registered protocol family 16
[ 0.344543] audit: initializing netlink subsys (disabled)
[ 0.344543] audit: type=2000 audit(1587451867.124:1): state=initialized audit_enabled=0 res=1
[ 0.344543] EISA bus registered
[ 0.344543] cpuidle: using governor ladder
[ 0.344543] cpuidle: using governor menu
[ 0.344543] ACPI: bus type PCI registered
[ 0.344543] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.344543] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.344543] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.344543] PCI: Using configuration type 1 for base access
[ 0.349109] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.349109] ACPI: Added _OSI(Module Device)
[ 0.349109] ACPI: Added _OSI(Processor Device)
[ 0.349109] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.349109] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.349109] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.349109] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.349592] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[ 0.355899] ACPI: 3 ACPI AML tables successfully acquired and loaded
[ 0.359638] ACPI: Dynamic OEM Table Load:
[ 0.359701] ACPI: SSDT 0xFFFF91B13AAEC600 000087 (v01 PmRef Cpu1Ist 00003000 INTL 20041203)
[ 0.360380] ACPI: Interpreter enabled
[ 0.360459] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.360509] ACPI: Using PIC for interrupt routing
[ 0.360615] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.360971] ACPI: Enabled 6 GPEs in block 00 to 0F
[ 0.361025] ACPI: Enabled 2 GPEs in block 10 to 1F
[ 0.368189] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.368248] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.368315] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.368444] acpi PNP0A08:00: host bridge window expanded to [io 0x1100-0xffff]; [io 0x1100-0xffff window] ignored
[ 0.368788] PCI host bridge to bus 0000:00
[ 0.368838] pci_bus 0000:00: root bus resource [io 0x0000-0x047f window]
[ 0.368890] pci_bus 0000:00: root bus resource [io 0x0480-0x048f]
[ 0.368941] pci_bus 0000:00: root bus resource [io 0x0490-0x0cf7 window]
[ 0.368992] pci_bus 0000:00: root bus resource [io 0x0d00-0x0fff window]
[ 0.369044] pci_bus 0000:00: root bus resource [io 0x1000-0x10cf]
[ 0.369094] pci_bus 0000:00: root bus resource [io 0x1100-0xffff]
[ 0.369145] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.369207] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff window]
[ 0.369269] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.369329] pci 0000:00:00.0: [1039:0671] type 00 class 0x060000
[ 0.369499] pci 0000:00:01.0: [1039:0004] type 01 class 0x060400
[ 0.369538] pci 0000:00:01.0: enabling Extended Tags
[ 0.369631] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.369758] pci 0000:00:02.0: [1039:0968] type 00 class 0x060100
[ 0.369943] pci 0000:00:02.5: [1039:5513] type 00 class 0x01018a
[ 0.369962] pci 0000:00:02.5: reg 0x10: [io 0x01f0-0x01f7]
[ 0.369971] pci 0000:00:02.5: reg 0x14: [io 0x03f4-0x03f7]
[ 0.369979] pci 0000:00:02.5: reg 0x18: [io 0x0170-0x0177]
[ 0.369988] pci 0000:00:02.5: reg 0x1c: [io 0x0374-0x0377]
[ 0.369997] pci 0000:00:02.5: reg 0x20: [io 0x4000-0x400f]
[ 0.370016] pci 0000:00:02.5: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.370068] pci 0000:00:02.5: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.370119] pci 0000:00:02.5: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.370171] pci 0000:00:02.5: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.370247] pci 0000:00:02.5: PME# supported from D3cold
[ 0.370375] pci 0000:00:03.0: [1039:7001] type 00 class 0x0c0310
[ 0.370392] pci 0000:00:03.0: reg 0x10: [mem 0xfdfff000-0xfdffffff]
[ 0.370558] pci 0000:00:03.1: [1039:7001] type 00 class 0x0c0310
[ 0.370575] pci 0000:00:03.1: reg 0x10: [mem 0xfdffe000-0xfdffefff]
[ 0.370745] pci 0000:00:03.3: [1039:7002] type 00 class 0x0c0320
[ 0.370763] pci 0000:00:03.3: reg 0x10: [mem 0xfdffd000-0xfdffdfff]
[ 0.370833] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[ 0.370959] pci 0000:00:04.0: [1039:0191] type 00 class 0x020000
[ 0.370978] pci 0000:00:04.0: reg 0x10: [mem 0xfdffc000-0xfdffc07f]
[ 0.370986] pci 0000:00:04.0: reg 0x14: [io 0xfe00-0xfe7f]
[ 0.371049] pci 0000:00:04.0: supports D1 D2
[ 0.371051] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.371172] pci 0000:00:05.0: [1039:1183] type 00 class 0x010185
[ 0.371191] pci 0000:00:05.0: reg 0x10: [io 0xfd00-0xfd07]
[ 0.371200] pci 0000:00:05.0: reg 0x14: [io 0xfc00-0xfc03]
[ 0.371208] pci 0000:00:05.0: reg 0x18: [io 0xfb00-0xfb07]
[ 0.371217] pci 0000:00:05.0: reg 0x1c: [io 0xfa00-0xfa03]
[ 0.371226] pci 0000:00:05.0: reg 0x20: [io 0xf900-0xf90f]
[ 0.371269] pci 0000:00:05.0: PME# supported from D3cold
[ 0.371395] pci 0000:00:06.0: [1039:000a] type 01 class 0x060400
[ 0.371434] pci 0000:00:06.0: enabling Extended Tags
[ 0.371532] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[ 0.371669] pci 0000:00:0d.0: [168c:0029] type 00 class 0x028000
[ 0.371689] pci 0000:00:0d.0: reg 0x10: [mem 0xfdfe0000-0xfdfeffff]
[ 0.371763] pci 0000:00:0d.0: PME# supported from D0 D3hot
[ 0.371895] pci 0000:00:0e.0: [10ec:8139] type 00 class 0x020000
[ 0.371914] pci 0000:00:0e.0: reg 0x10: [io 0xf600-0xf6ff]
[ 0.371923] pci 0000:00:0e.0: reg 0x14: [mem 0xfdffb000-0xfdffb0ff]
[ 0.371962] pci 0000:00:0e.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.371990] pci 0000:00:0e.0: supports D1 D2
[ 0.371992] pci 0000:00:0e.0: PME# supported from D1 D2 D3hot D3cold
[ 0.372109] pci 0000:00:0f.0: [1039:7502] type 00 class 0x040300
[ 0.372128] pci 0000:00:0f.0: reg 0x10: [mem 0xfdff4000-0xfdff7fff]
[ 0.372198] pci 0000:00:0f.0: PME# supported from D0 D3hot D3cold
[ 0.372390] pci 0000:01:00.0: [10de:01df] type 00 class 0x030000
[ 0.372409] pci 0000:01:00.0: reg 0x10: [mem 0xfa000000-0xfaffffff]
[ 0.372422] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.372434] pci 0000:01:00.0: reg 0x1c: [mem 0xfb000000-0xfbffffff 64bit]
[ 0.372450] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.372557] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.372630] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.372683] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.372687] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfcffffff]
[ 0.372692] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.372743] pci 0000:00:06.0: PCI bridge to [bus 02]
[ 0.372797] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
[ 0.372800] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.372806] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.372963] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.373123] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
[ 0.373281] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.373440] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.373599] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.373758] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
[ 0.373916] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.374074] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.375190] SCSI subsystem initialized
[ 0.375190] libata version 3.00 loaded.
[ 0.375858] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[ 0.375880] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.375943] pci 0000:01:00.0: vgaarb: bridge control possible
[ 0.375993] vgaarb: loaded
[ 0.376072] ACPI: bus type USB registered
[ 0.376140] usbcore: registered new interface driver usbfs
[ 0.376202] usbcore: registered new interface driver hub
[ 0.376269] usbcore: registered new device driver usb
[ 0.376361] pps_core: LinuxPPS API ver. 1 registered
[ 0.376410] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.376475] PTP clock support registered
[ 0.376544] EDAC MC: Ver: 3.0.0
[ 0.376544] PCI: Using ACPI for IRQ routing
[ 0.385708] PCI: pci_cache_line_size set to 64 bytes
[ 0.385752] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
[ 0.385754] e820: reserve RAM buffer [mem 0x7fff0000-0x7fffffff]
[ 0.385921] NetLabel: Initializing
[ 0.385969] NetLabel: domain hash size = 128
[ 0.386017] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.386088] NetLabel: unlabeled traffic allowed by default
[ 0.386161] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.386161] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.386161] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.387847] clocksource: Switched to clocksource tsc-early
[ 0.413025] VFS: Disk quotas dquot_6.6.0
[ 0.413137] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.413483] AppArmor: AppArmor Filesystem Enabled
[ 0.413633] pnp: PnP ACPI init
[ 0.414279] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 0.414330] system 00:00: [io 0x0800-0x0805] has been reserved
[ 0.414383] system 00:00: [io 0x0290-0x0297] has been reserved
[ 0.414433] system 00:00: [io 0x0880-0x088f] has been reserved
[ 0.414490] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.414586] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.414824] pnp 00:02: [dma 2]
[ 0.414867] pnp 00:02: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.415232] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.415601] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.416075] pnp 00:05: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.416309] system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.416365] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.416470] system 00:07: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.416523] system 00:07: [mem 0xfed00000-0xfed000ff] has been reserved
[ 0.416575] system 00:07: [mem 0xfed30000-0xfed300ff] has been reserved
[ 0.416626] system 00:07: [mem 0x7fff0000-0x7fffffff] could not be reserved
[ 0.416678] system 00:07: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.416730] system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.416782] system 00:07: [mem 0x00100000-0x7ffeffff] could not be reserved
[ 0.416834] system 00:07: [mem 0xffee0000-0xffefffff] has been reserved
[ 0.416886] system 00:07: [mem 0xfffe0000-0xfffeffff] has been reserved
[ 0.416939] system 00:07: [mem 0xfec00000-0xfecfffff] has been reserved
[ 0.416990] system 00:07: [mem 0xfee00000-0xfeefffff] has been reserved
[ 0.417046] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.417056] pnp: PnP ACPI: found 8 devices
[ 0.424102] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.424205] pci 0000:00:0e.0: BAR 6: assigned [mem 0x80000000-0x8000ffff pref]
[ 0.424270] pci 0000:01:00.0: BAR 6: assigned [mem 0xfc000000-0xfc01ffff pref]
[ 0.424332] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.424384] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.424438] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfcffffff]
[ 0.424491] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.424558] pci 0000:00:06.0: PCI bridge to [bus 02]
[ 0.424608] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
[ 0.424662] pci 0000:00:06.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 0.424716] pci 0000:00:06.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.424783] pci_bus 0000:00: resource 4 [io 0x0000-0x047f window]
[ 0.424785] pci_bus 0000:00: resource 5 [io 0x0480-0x048f]
[ 0.424786] pci_bus 0000:00: resource 6 [io 0x0490-0x0cf7 window]
[ 0.424788] pci_bus 0000:00: resource 7 [io 0x0d00-0x0fff window]
[ 0.424789] pci_bus 0000:00: resource 8 [io 0x1000-0x10cf]
[ 0.424791] pci_bus 0000:00: resource 9 [io 0x1100-0xffff]
[ 0.424792] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff window]
[ 0.424794] pci_bus 0000:00: resource 11 [mem 0x80000000-0xfebfffff window]
[ 0.424796] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.424797] pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfcffffff]
[ 0.424799] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.424801] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.424802] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
[ 0.424804] pci_bus 0000:02: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
[ 0.424917] NET: Registered protocol family 2
[ 0.425319] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes)
[ 0.425403] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.425601] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.425892] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.426048] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.426134] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.426282] NET: Registered protocol family 1
[ 0.426342] NET: Registered protocol family 44
[ 0.426763] PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 0.426814] PCI: setting IRQ 11 as level-triggered
[ 0.459541] pci 0000:00:03.0: quirk_usb_early_handoff+0x0/0x6a0 took 32341 usecs
[ 0.459879] PCI Interrupt Link [LNKF] enabled at IRQ 15
[ 0.459930] PCI: setting IRQ 15 as level-triggered
[ 0.491730] pci 0000:00:03.1: quirk_usb_early_handoff+0x0/0x6a0 took 31347 usecs
[ 0.492068] PCI Interrupt Link [LNKG] enabled at IRQ 9
[ 0.492119] PCI: setting IRQ 9 as level-triggered
[ 0.492313] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.492378] PCI: CLS 64 bytes, default 64
[ 0.492464] Unpacking initramfs...
[ 9.795326] Freeing initrd memory: 38632K
[ 9.796144] check: Scanning for low memory corruption every 60 seconds
[ 9.797485] Initialise system trusted keyrings
[ 9.797556] Key type blacklist registered
[ 9.797824] workingset: timestamp_bits=36 max_order=19 bucket_order=0
[ 9.800765] zbud: loaded
[ 9.801512] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 9.801950] fuse init (API version 7.28)
[ 9.850192] Key type asymmetric registered
[ 9.850249] Asymmetric key parser 'x509' registered
[ 9.850333] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 9.850457] io scheduler mq-deadline registered
[ 9.850916] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.851076] intel_idle: does not run on family 6 model 15
[ 9.851229] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 9.851311] ACPI: Power Button [PWRB]
[ 9.851434] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 9.851523] ACPI: Power Button [PWRF]
[ 9.852593] thermal LNXTHERM:00: registered as thermal_zone0
[ 9.852644] ACPI: Thermal Zone [THRM] (36 C)
[ 9.852913] thermal LNXTHERM:01: registered as thermal_zone1
[ 9.852963] ACPI: Thermal Zone [SYST] (40 C)
[ 9.853217] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 9.873806] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 9.894290] 00:04: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 9.896764] Linux agpgart interface v0.103
[ 9.900689] loop: module loaded
[ 9.901098] pata_sis 0000:00:02.5: version 0.5.2
[ 9.901525] PCI Interrupt Link [LNKA] enabled at IRQ 5
[ 9.901577] PCI: setting IRQ 5 as level-triggered
[ 9.902617] scsi host0: pata_sis
[ 9.902885] scsi host1: pata_sis
[ 9.902999] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x4000 irq 14
[ 9.903051] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x4008 irq 15
[ 9.903261] libphy: Fixed MDIO Bus: probed
[ 9.903310] tun: Universal TUN/TAP device driver, 1.6
[ 9.903431] PPP generic driver version 2.4.2
[ 9.903552] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.903608] ehci-pci: EHCI PCI platform driver
[ 9.903898] ehci-pci 0000:00:03.3: EHCI Host Controller
[ 9.905323] ehci-pci 0000:00:03.3: new USB bus registered, assigned bus number 1
[ 9.905433] ehci-pci 0000:00:03.3: cache line size of 64 is not supported
[ 9.905441] ehci-pci 0000:00:03.3: irq 9, io mem 0xfdffd000
[ 9.919847] ehci-pci 0000:00:03.3: USB 2.0 started, EHCI 1.00
[ 9.920020] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[ 9.920096] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.920158] usb usb1: Product: EHCI Host Controller
[ 9.920209] usb usb1: Manufacturer: Linux 5.0.0-32-generic ehci_hcd
[ 9.920260] usb usb1: SerialNumber: 0000:00:03.3
[ 9.920454] hub 1-0:1.0: USB hub found
[ 9.920512] hub 1-0:1.0: 8 ports detected
[ 9.920824] ehci-platform: EHCI generic platform driver
[ 9.920891] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.920944] ohci-pci: OHCI PCI platform driver
[ 9.921163] ohci-pci 0000:00:03.0: OHCI PCI host controller
[ 9.921219] ohci-pci 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 9.921305] ohci-pci 0000:00:03.0: irq 11, io mem 0xfdfff000
[ 9.981975] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00
[ 9.982039] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.982100] usb usb2: Product: OHCI PCI host controller
[ 9.982150] usb usb2: Manufacturer: Linux 5.0.0-32-generic ohci_hcd
[ 9.982201] usb usb2: SerialNumber: 0000:00:03.0
[ 9.982368] hub 2-0:1.0: USB hub found
[ 9.982425] hub 2-0:1.0: 4 ports detected
[ 9.982797] ohci-pci 0000:00:03.1: OHCI PCI host controller
[ 9.982852] ohci-pci 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 9.982930] ohci-pci 0000:00:03.1: irq 15, io mem 0xfdffe000
[ 10.041878] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00
[ 10.041942] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.042003] usb usb3: Product: OHCI PCI host controller
[ 10.042053] usb usb3: Manufacturer: Linux 5.0.0-32-generic ohci_hcd
[ 10.042104] usb usb3: SerialNumber: 0000:00:03.1
[ 10.042271] hub 3-0:1.0: USB hub found
[ 10.042327] hub 3-0:1.0: 4 ports detected
[ 10.042542] ohci-platform: OHCI generic platform driver
[ 10.042601] uhci_hcd: USB Universal Host Controller Interface driver
[ 10.042732] i8042: PNP: No PS/2 controller found.
[ 10.042780] i8042: Probing ports directly.
[ 10.043178] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.043232] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 10.043437] mousedev: PS/2 mouse device common for all mice
[ 10.043668] rtc_cmos 00:01: RTC can wake from S4
[ 10.043933] rtc_cmos 00:01: registered as rtc0
[ 10.044009] rtc_cmos 00:01: alarms up to one year, 242 bytes nvram, hpet irqs
[ 10.044069] i2c /dev entries driver
[ 10.044261] device-mapper: uevent: version 1.0.3
[ 10.044399] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 10.044490] platform eisa.0: Probing EISA bus 0
[ 10.044542] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 10.044594] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 10.044645] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 10.044697] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 10.044748] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 10.044799] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 10.044850] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 10.044901] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 10.044952] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 10.045003] platform eisa.0: EISA: Detected 0 cards
[ 10.045089] ledtrig-cpu: registered to indicate activity on CPUs
[ 10.045502] NET: Registered protocol family 10
[ 10.053155] Segment Routing with IPv6
[ 10.053245] NET: Registered protocol family 17
[ 10.053354] Key type dns_resolver registered
[ 10.053681] mce: Using 6 MCE banks
[ 10.053759] RAS: Correctable Errors collector initialized.
[ 10.053868] microcode: sig=0x6f6, pf=0x1, revision=0xc6
[ 10.053967] microcode: Microcode Update Driver: v2.2.
[ 10.053988] sched_clock: Marking stable (10043800638, 10160774)->(10059240842, -5279430)
[ 10.054334] registered taskstats version 1
[ 10.054404] Loading compiled-in X.509 certificates
[ 10.056843] Loaded X.509 cert 'Build time autogenerated kernel key: 8248cf0f90a942a6d35391b2654e2baeb494e1df'
[ 10.056949] zswap: loaded using pool lzo/zbud
[ 10.063777] Key type big_key registered
[ 10.063853] Key type trusted registered
[ 10.067096] Key type encrypted registered
[ 10.067148] AppArmor: AppArmor sha1 policy hashing enabled
[ 10.067210] ima: No TPM chip found, activating TPM-bypass!
[ 10.067265] ima: Allocated hash algorithm: sha1
[ 10.067331] No architecture policies found
[ 10.067393] evm: Initialising EVM extended attributes:
[ 10.067443] evm: security.selinux
[ 10.067489] evm: security.SMACK64
[ 10.067536] evm: security.SMACK64EXEC
[ 10.067583] evm: security.SMACK64TRANSMUTE
[ 10.067631] evm: security.SMACK64MMAP
[ 10.067678] evm: security.apparmor
[ 10.067724] evm: security.ima
[ 10.067770] evm: security.capability
[ 10.067829] evm: HMAC attrs: 0x1
[ 10.068344] Magic number: 0:539:873
[ 10.068605] rtc_cmos 00:01: setting system clock to 2020-04-21T06:51:17 UTC (1587451877)
[ 10.080103] ata1.01: ATAPI: HL-DT-ST DVD-RW_GSA-H41N, RA00, max UDMA/66
[ 10.110036] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RW_GSA-H41N RA00 PQ: 0 ANSI: 5
[ 10.171488] sr 0:0:1:0: [sr0] scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 10.171555] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 10.171930] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 10.172009] sr 0:0:1:0: Attached scsi generic sg0 type 5
[ 10.172158] ata2: port disabled--ignoring
[ 10.174782] Freeing unused decrypted memory: 2040K
[ 10.176675] Freeing unused kernel image memory: 2588K
[ 10.187904] Write protecting the kernel read-only data: 22528k
[ 10.190003] Freeing unused kernel image memory: 2016K
[ 10.191791] Freeing unused kernel image memory: 1736K
[ 10.208231] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 10.208298] x86/mm: Checking user space page tables
[ 10.224362] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 10.224422] Run /init as init process
[ 10.345562] hpet1: lost 17 rtc interrupts
[ 10.358911] sis190: sis190 Gigabit Ethernet driver 1.4 loaded
[ 10.359985] PCI Interrupt Link [LNKB] enabled at IRQ 15
[ 10.362433] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.362490] 8139cp 0000:00:0e.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 10.364695] PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 10.364789] sis190: 0000:00:04.0: Read MAC address from EEPROM
[ 10.364840] sis190: 0000:00:04.0: Error EEPROM read 0
[ 10.364890] sis190: 0000:00:04.0: Read MAC address from APC
[ 10.365084] sata_sis 0000:00:05.0: version 1.0
[ 10.365236] sata_sis 0000:00:05.0: Detected SiS 1183/966/966L/968/680 controller in PATA mode
[ 10.367882] FDC 0 is a post-1991 82077
[ 10.371932] scsi host2: sata_sis
[ 10.372666] scsi host3: sata_sis
[ 10.372781] ata3: PATA max UDMA/133 cmd 0xfd00 ctl 0xfc00 bmdma 0xf900 irq 15
[ 10.372835] ata4: PATA max UDMA/133 cmd 0xfb00 ctl 0xfa00 bmdma 0xf908 irq 15
[ 10.388667] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 10.392400] PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 10.392455] PCI: setting IRQ 10 as level-triggered
[ 10.393036] 8139too 0000:00:0e.0 eth0: RealTek RTL8139 at 0x(____ptrval____), 00:05:1c:21:1f:f1, IRQ 10
[ 10.434096] 8139too 0000:00:0e.0 enp0s14: renamed from eth0
[ 10.435915] sis190: 0000:00:04.0: unknown PHY 0x1c:0xc910 transceiver at address 1
[ 10.515878] usb 2-1: new low-speed USB device number 2 using ohci-pci
[ 10.538316] ata3.00: ATA-9: SAMSUNG MZAPF032HCFV-000H1, FXM21H2Q, max UDMA/133
[ 10.538390] ata3.00: 62533296 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 10.541985] scsi 2:0:0:0: Direct-Access ATA SAMSUNG MZAPF032 1H2Q PQ: 0 ANSI: 5
[ 10.542427] sd 2:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB)
[ 10.542432] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 10.542504] sd 2:0:0:0: [sda] Write Protect is off
[ 10.542594] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 10.542623] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.543309] sda: sda1 sda2
[ 10.544017] sd 2:0:0:0: [sda] Attached SCSI disk
[ 10.757900] usb 2-1: New USB device found, idVendor=045e, idProduct=0040, bcdDevice= 3.00
[ 10.757974] usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0
[ 10.758030] usb 2-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
[ 10.758084] usb 2-1: Manufacturer: Microsoft
[ 10.765738] hidraw: raw HID events driver (C) Jiri Kosina
[ 10.774258] usbcore: registered new interface driver usbhid
[ 10.774311] usbhid: USB HID core driver
[ 10.776966] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:03.0/usb2/2-1/2-1:1.0/0003:045E:0040.0001/input/input5
[ 10.777192] hid-generic 0003:045E:0040.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:03.0-1/input0
[ 10.811851] tsc: Refined TSC clocksource calibration: 2400.084 MHz
[ 10.811911] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x229886f1f14, max_idle_ns: 440795306808 ns
[ 10.811999] clocksource: Switched to clocksource tsc
[ 11.227848] sis190: 0000:00:04.0: Using transceiver at address 1 as default
[ 11.276157] sis190 0000:00:04.0 eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at (____ptrval____) (IRQ: 11), 00:1c:25:28:53:9d
[ 11.277592] sis190 0000:00:04.0 eth0: RGMII mode.
[ 11.277644] sis190 0000:00:04.0 eth0: Enabling Auto-negotiation
[ 11.291850] usb 3-1: new low-speed USB device number 2 using ohci-pci
[ 11.324899] sis190 0000:00:04.0 enp0s4: renamed from eth0
[ 11.517951] usb 3-1: New USB device found, idVendor=04f3, idProduct=0103, bcdDevice= 1.05
[ 11.518019] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 11.529505] input: HID 04f3:0103 as /devices/pci0000:00/0000:00:03.1/usb3/3-1/3-1:1.0/0003:04F3:0103.0002/input/input6
[ 11.529658] hid-generic 0003:04F3:0103.0002: input,hidraw1: USB HID v1.10 Keyboard [HID 04f3:0103] on usb-0000:00:03.1-1/input0
[ 11.537559] input: HID 04f3:0103 Consumer Control as /devices/pci0000:00/0000:00:03.1/usb3/3-1/3-1:1.1/0003:04F3:0103.0003/input/input7
[ 11.537706] input: HID 04f3:0103 System Control as /devices/pci0000:00/0000:00:03.1/usb3/3-1/3-1:1.1/0003:04F3:0103.0003/input/input8
[ 11.537848] hid-generic 0003:04F3:0103.0003: input,hidraw2: USB HID v1.10 Device [HID 04f3:0103] on usb-0000:00:03.1-1/input1
[ 13.207422] random: fast init done
[ 13.225929] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.226015] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.226074] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 13.226778] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 13.230872] ISO 9660 Extensions: RRIP_1991A
[ 19.191573] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 19.207931] systemd[1]: Detected architecture x86-64.
[ 19.212365] systemd[1]: Set hostname to <mint>.
[ 19.371780] systemd[1]: Unnecessary job for /dev/loop0 was removed.
[ 19.372271] systemd[1]: Reached target Remote File Systems.
[ 19.373034] systemd[1]: Created slice User and Session Slice.
[ 19.373358] systemd[1]: Reached target User and Group Name Lookups.
[ 19.373683] systemd[1]: Reached target System Time Synchronized.
[ 19.374061] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 19.374396] systemd[1]: Reached target Swap.
[ 19.505611] lp: driver loaded but no devices found
[ 19.530369] ppdev: user-space parallel port driver
[ 19.535743] parport_pc 00:05: reported by Plug and Play ACPI
[ 19.535958] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 19.632083] lp0: using parport0 (interrupt-driven).
[ 19.728478] systemd-journald[805]: Received request to flush runtime journal from PID 1
[ 20.707962] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 20.770416] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 21.637494] coretemp coretemp.0: Using relative temperature scale!
[ 21.781035] coretemp coretemp.0: Using relative temperature scale!
[ 21.790676] intel_powerclamp: No package C-state available
[ 21.861715] intel_powerclamp: No package C-state available
[ 23.971960] ath: EEPROM regdomain: 0x809c
[ 23.971962] ath: EEPROM indicates we should expect a country code
[ 23.971964] ath: doing EEPROM country->regdmn map search
[ 23.971965] ath: country maps to regdmn code: 0x52
[ 23.971966] ath: Country alpha2 being used: CN
[ 23.971967] ath: Regpair used: 0x52
[ 24.089309] snd_hda_intel 0000:00:0f.0: CORB reset timeout#1, CORBRP = 0
[ 24.111446] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 24.112543] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xffffb15540940000, irq=15
[ 24.145159] 8139too 0000:00:0e.0 enp0s14: link down
[ 24.167415] ath9k 0000:00:0d.0 wlp0s13: renamed from wlan0
[ 24.213328] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC883: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 24.213340] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 24.213342] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 24.213343] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 24.213345] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x1e/0x0
[ 24.213346] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 24.213348] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
[ 24.213351] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
[ 24.213352] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
[ 24.213354] snd_hda_codec_realtek hdaudioC0D0: Aux=0x1c
[ 24.297443] input: HDA SIS966 Rear Mic as /devices/pci0000:00/0000:00:0f.0/sound/card0/input9
[ 24.297563] input: HDA SIS966 Line as /devices/pci0000:00/0000:00:0f.0/sound/card0/input10
[ 24.297646] input: HDA SIS966 Line Out Front as /devices/pci0000:00/0000:00:0f.0/sound/card0/input11
[ 24.297731] input: HDA SIS966 Line Out Surround as /devices/pci0000:00/0000:00:0f.0/sound/card0/input12
[ 24.297817] input: HDA SIS966 Line Out CLFE as /devices/pci0000:00/0000:00:0f.0/sound/card0/input13
[ 24.297895] input: HDA SIS966 Line Out Side as /devices/pci0000:00/0000:00:0f.0/sound/card0/input14
[ 34.275890] sis190 0000:00:04.0 enp0s4: auto-negotiating...
[ 41.543956] random: crng init done
[ 41.543961] random: 7 urandom warning(s) missed due to ratelimiting
[ 43.297647] perf: interrupt took too long (2502 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 89.644219] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 89.661265] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 89.663004] wlp0s13: authenticated
[ 89.667878] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 89.671584] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=5)
[ 89.671747] wlp0s13: associated
[ 89.752000] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s13: link becomes ready
[ 94.139153] perf: interrupt took too long (3170 > 3127), lowering kernel.perf_event_max_sample_rate to 63000
[ 123.469841] perf: interrupt took too long (3971 > 3962), lowering kernel.perf_event_max_sample_rate to 50250
[ 172.058722] perf: interrupt took too long (4973 > 4963), lowering kernel.perf_event_max_sample_rate to 40000
[ 243.023432] perf: interrupt took too long (6219 > 6216), lowering kernel.perf_event_max_sample_rate to 32000
[ 533.332443] perf: interrupt took too long (7849 > 7773), lowering kernel.perf_event_max_sample_rate to 25250
[ 1241.385363] perf: interrupt took too long (9816 > 9811), lowering kernel.perf_event_max_sample_rate to 20250
[ 2081.491056] INFO: NMI handler (perf_event_nmi_handler) took too long to run: 1.432 msecs
[ 5011.633614] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 5011.658028] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 5011.660151] wlp0s13: authenticated
[ 5011.695963] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 5011.699660] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 5011.699879] wlp0s13: associated
[ 6491.985682] wlp0s13: deauthenticated from 10:c3:7b:d4:40:ac (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
[ 6492.124897] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 6492.147954] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 6492.149681] wlp0s13: authenticated
[ 6492.156197] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 6492.159864] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 6492.160060] wlp0s13: associated
[ 6551.983765] wlp0s13: deauthenticated from 10:c3:7b:d4:40:ac (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
[ 6552.120250] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 6552.147486] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 6552.150128] wlp0s13: authenticated
[ 6552.151556] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 6552.155866] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 6552.156031] wlp0s13: associated
[ 6631.579473] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 6631.595613] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 6631.602442] wlp0s13: authenticated
[ 6631.610416] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 6631.614944] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 6631.615129] wlp0s13: associated
[ 6929.499616] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 6929.517670] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 6929.520531] wlp0s13: authenticated
[ 6929.531087] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 6929.534782] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 6929.534966] wlp0s13: associated
[ 8538.967396] wlp0s13: deauthenticated from 10:c3:7b:d4:40:ac (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
[ 8539.116369] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 8539.135683] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 8539.137442] wlp0s13: authenticated
[ 8539.152218] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 8539.156405] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=4)
[ 8539.156611] wlp0s13: associated
[ 8977.938099] wlp0s13: deauthenticated from 10:c3:7b:d4:40:ac (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
[ 8978.037417] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 8978.056658] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 8978.061957] wlp0s13: authenticated
[ 8978.085592] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 8978.089402] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=1)
[ 8978.089633] wlp0s13: associated
[ 9775.481742] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[ 9775.512685] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[ 9775.515572] wlp0s13: authenticated
[ 9775.548490] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[ 9775.553782] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=1)
[ 9775.553941] wlp0s13: associated
[ 9897.725714] INFO: NMI handler (perf_event_nmi_handler) took too long to run: 2.390 msecs
[ 9897.725718] perf: interrupt took too long (27655 > 12270), lowering kernel.perf_event_max_sample_rate to 7000
[15164.855388] wlp0s13: deauthenticated from 10:c3:7b:d4:40:ac (Reason: 7=CLASS3_FRAME_FROM_NONASSOC_STA)
[15164.992880] wlp0s13: authenticate with 10:c3:7b:d4:40:ac
[15165.008703] wlp0s13: send auth to 10:c3:7b:d4:40:ac (try 1/3)
[15165.010432] wlp0s13: authenticated
[15165.012781] wlp0s13: associate with 10:c3:7b:d4:40:ac (try 1/3)
[15165.016382] wlp0s13: RX AssocResp from 10:c3:7b:d4:40:ac (capab=0x411 status=0 aid=1)
[15165.016597] wlp0s13: associated
[24877.876676] INFO: NMI handler (nmi_cpu_backtrace_handler) took too long to run: 2.409 msecs
[28455.614746] INFO: NMI handler (perf_event_nmi_handler) took too long to run: 3.188 msecs
[33614.934654] INFO: NMI handler (perf_event_nmi_handler) took too long to run: 3.516 msecs
[33614.934657] perf: interrupt took too long (36439 > 34568), lowering kernel.perf_event_max_sample_rate to 5250
[47946.680615] INFO: NMI handler (perf_event_nmi_handler) took too long to run: 3.677 msecs
[65276.534383] INFO: NMI handler (nmi_cpu_backtrace_handler) took too long to run: 3.163 msecs
Naposledy upravil(a) etis dne 22 dub 2020, 18:14, celkem upraveno 1 x.
Re: SIS chipset
Tak jo - zase nekdo, kdo si asi nic neprecetl o tom, jak fungovat na foru. Takze prosim uprav svuj prispevek a veskery vypis dej do tzv. kodu. Je na to ikona, kdyz se prepnes do pokrocilejsiho rezimu editace.
Zvuky jsou mantrami a myšlenky moudrostí, prostě proto, že se mohou objevovat ...
Re: SIS chipset
.
Ano mohol si dat ten vypis do code (vlozit ako kod)
Ked takto to funguje, tak staci to nainstalovat a nasledne upravit v instalovanom systeme subor grub v ceste /etc/default/
Tam byva podobny riadok
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
a upravit na
GRUB_CMDLINE_LINUX_DEFAULT="quiet xforcevesa nomodeset"
ulozit
Aktualizovat nastavenie grubu zadanim prikazu do terminalu:
Nasledne restart.
.
Ano mohol si dat ten vypis do code (vlozit ako kod)
Ked takto to funguje, tak staci to nainstalovat a nasledne upravit v instalovanom systeme subor grub v ceste /etc/default/
Kód: Vybrat vše
/etc/default/grub
Tam byva podobny riadok
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
a upravit na
GRUB_CMDLINE_LINUX_DEFAULT="quiet xforcevesa nomodeset"
ulozit
Aktualizovat nastavenie grubu zadanim prikazu do terminalu:
Kód: Vybrat vše
sudo update-grub
.
.
Re: SIS chipset
Môžem to skúsiť nainštalovať a potom z LIVE to nájsť a upraviť.... Dám vedieť...
Tak dnes PC "odišiel", takže som ho musel nahradiť. AK by som ho zas "oživil" skúsim....
Ďakujem
Tak dnes PC "odišiel", takže som ho musel nahradiť. AK by som ho zas "oživil" skúsim....
Ďakujem